SPC, LVT, WPC and PVC, floors and panels.Purchasing office · Floors, panels & surfaces
More in Specs & quotes

Specs & quotes / Acoustics

Acoustic SPC flooring: how to specify and verify the sound rating

Acoustic SPC flooring claims rest on one lab build-up: ASTM E2179 rates the covering on a concrete slab, not your building. What to ask for.

Short answer

Ask for a laboratory report, not a datasheet figure. It should name the method (ISO 10140-3 with ISO 717-2, or ASTM E492 or E2179), the test floor, and the exact board and pad tested, with thicknesses and pad grade. Check whether the figure is sound heard downstairs or noise in the room itself, and write the tested build-up into your specification so production cannot drift from it.

01

ASTM E2179 states that the same floor covering on different base floors will not always give the same IIC rating; its ΔIIC describes the covering on a concrete slab only.

02

EN 16205:2020 measures the noise a floor covering radiates into the room where people walk, a different quantity from the impact sound transmitted to the room below.

03

The MMFA, the European multilayer flooring association, says the floor maker’s underlay requirements are binding in terms of warranty; a second pad therefore needs the maker’s written approval.

An acoustic figure on an SPC datasheet is the result of one test, on one floor, with one build-up. Whether it describes the boards in your container depends on three things the datasheet rarely states: which method produced it, what the board sat on, and which pad was attached. This guide covers how to specify acoustic performance so that a report can be checked against the product you order.

What should an acoustic SPC claim state?

The method, the test floor and the exact build-up tested. A number without those three is not comparable with another factory’s number and cannot be tied to your SKU. The table sets out the ratings you are likely to see, which document defines each, and what each one tells you as a buyer.

The table is built from the published scopes of the ISO, ASTM and CEN documents named; the full standards are sold documents.

Metric Method What it tells you
ΔLw (weighted reduction in impact sound pressure level) Measured under ISO 10140-3, rated under ISO 717-2 How much the covering reduces tapping-machine sound transmitted through a reference floor; the covering’s own contribution
Ln,w (weighted normalised impact sound pressure level) ISO 10140-3, ISO 717-2 Sound level in the room below for the whole floor tested, covering included; lower is better
IIC (impact insulation class) ASTM E492, rated under ASTM E989 The whole floor-ceiling assembly in a laboratory; the rating rises as attenuation rises
ΔIIC (change in impact insulation class) ASTM E2179, rated under ASTM E989 The covering’s improvement on a standard concrete floor
AIIC, ISR, NISR ASTM E1007 (field) A finished building, flanking included; belongs to that building, not to the product
Walking noise level EN 16205 Noise radiated into the room where people walk, on a standard concrete floor
STC (sound transmission class) ASTM E90, rated under ASTM E413 Airborne sound through a partition; says nothing about footsteps

Two pairs cause most of the confusion. IIC and ΔIIC look alike, but IIC rates the whole assembly, slab and ceiling below included, while ΔIIC isolates the covering. ΔLw and Ln,w sit in the same relation on the ISO side. ASTM E2179-25 also reports a ΔHIIC, based on the high-frequency impact insulation class of ASTM E3222, so ask which delta a datasheet is quoting. A datasheet that reports an IIC without the assembly is quoting a laboratory floor-ceiling, not the covering.

Next step: add the pad and the acoustic fields to your specification sheet.

Which noise is being measured: downstairs or in the room?

Impact sound ratings describe what the neighbour below hears. Walking noise describes what the person in the room hears. They are separate measurements with separate standards, and a soft pad that helps one does not necessarily help the other. Decide which complaint you are trying to prevent before you ask for a figure.

ISO 10140-3 specifies laboratory methods for measuring the impact sound insulation of floor assemblies, with the standard tapping machine representing footsteps in shoes; alternative sources represent bare feet or children jumping. ASTM E492 does the same job on the American side, measuring the sound transmitted into a receiving room directly below.

EN 16205:2020 measures something else: the noise radiated from a floor covering on a standard concrete floor when the tapping machine excites it, recorded in the room where the walking happens. The MMFA lists the two separately for underlays as well, as impact sound reduction (IS) and radiated walking sound (RWS).

Where a project’s designer sets an acoustic requirement, ask which metric and method it uses, then ask the factory which of the two quantities it has tested. A report on one says nothing about the other.

In England, Approved Document E (2003 edition incorporating the 2004 to 2015 amendments) sets sound insulation values for separating floors in flats, shown by pre-completion testing on site or, for new homes, by building to pre-approved separating floor designs. It states that site impact tests are normally made without a soft covering such as foam-backed vinyl, so a laboratory ΔLw for your covering does not show that a building complies.

Why does the test floor change the result?

Because the rating belongs to the assembly. ASTM E2179 says it plainly: the impact rating is set by the base floor and the covering together, which is why its method characterises the covering alone only when installed over concrete slab floors. A covering figure measured on concrete describes the covering on concrete.

The laboratory standards are written with that limit in mind. ISO 10140-3 states that its results are not directly applicable to the field without accounting for flanking transmission, boundary conditions and loss factor. ASTM E492 goes further: because the specimen is meant to be the only significant sound path, its ratings represent an upper limit to what would be measured in a field test.

The base floor matters most for timber and other lightweight structures. ASTM E2179 warns that its difference spectra shall not be used to estimate levels for floors made of one or two lightweight layers such as plywood or oriented strand board, and that estimates for joist floors with a thin concrete topping come out too low. ISO 717-2:2020 includes a separate procedure for the reduction by floor coverings on lightweight floors. A ΔLw or ΔIIC measured on a concrete slab is not a figure for a timber-joist flat.

One more check: ISO 16251-1, a small mock-up method, is restricted to soft, flexible coverings that pass impact sound into the floor locally, such as carpet, PVC and linoleum. If a rigid click board’s report cites it, ask the laboratory to confirm in writing that the method applies to that construction.

Tapping machine SPC board Attached pad (as tested) Separate underlay, if any Laboratory test floor Room where people walk EN 16205 Room below ISO 10140-3 / ASTM E492, E2179 A change to any layer is a different specimen.
Fig. 1One specimen, two measurement points. The report covers the layers that were on the test floor and nothing else.

Attached pad or a separate underlay?

Buy the acoustic performance as part of the board: an attached pad of a stated material, thickness and grade, tested with that board. A separate underlay added on site changes the specimen, so the factory’s report no longer describes the floor, and it may conflict with the installation instructions that the warranty depends on.

The MMFA treats the floor and its underlay as one system to be chosen for the use, to be read with the installation instructions of the specific product. On warranty it is direct: the requirements the floor manufacturer or supplier gives for using an underlay are binding in terms of warranty. It also notes that more elastic constructions need underlays with high compressive strength to avoid damage, and that the floor supplier should specify the underlay group.

Instructions differ between products, which is why the rule has to come from your own supplier. Roca Tile USA’s installation instructions for its Evolux rigid core vinyl flooring (March 2024) open with a capitalised warning that an additional underlayment pad will cause flexion and void the warranty. Further down, the same document allows a second underlayment of no more than 3 mm in residential use, states that IIC and STC laboratory testing on certain SPC products has not shown a second underlayment adding acoustic benefit, and warns that soft underlayment will compromise the locking ability. If a published installation sheet can hold both positions, a buyer cannot assume either.

For your own range, settle it in the specification and in the installation instructions you print: either no additional underlay, or one named underlay, with a maximum thickness and the compressive strength the factory requires, and a report on that combination if you plan to quote an acoustic figure for it. The joint is the part at risk; the locking-strength side is covered in what an SPC click joint test should establish.

The pad itself belongs among the materials released before extrusion starts, as set out in the production hold points.

How do you tie an acoustic report to one SKU?

Match the report field by field against your specification and the carton. If the board thickness, pad material, pad thickness or pad grade differ, the report belongs to another product. Then make the pad a controlled field, so a change of pad supplier during production needs your approval and a new report.

The table lists the fields we would check on any acoustic report before accepting it for an SKU.

Report field Check against If it does not match
Laboratory name and accreditation scope The method is inside the laboratory’s accredited scope Treat the result as indicative only
Method and edition (for example ISO 10140-3:2021 with ISO 717-2:2020, or ASTM E2179-25) The metric quoted on the datasheet The datasheet figure has no basis
Test floor description Concrete slab, lightweight floor, ceiling below Do not use the figure for a different structure
Board: product name, thickness, core Your specification sheet A different product was tested
Pad: material, thickness, density or grade code, supplier Your specification and the pad supplier’s sheet New construction: new sample and new report
Sample origin and date Drawn from production or submitted by the factory Ask which; a submitted sample proves less
Separate underlay, if any Your installation instructions The report covers a floor you do not sell

Read the report itself, not a summary page or a certificate built on it. Our guide to reading laboratory reports and certificates covers checking the holder, the scope and the date.

At pre-shipment, check that the pad is present, bonded and of the approved thickness, alongside the rest of the pre-shipment inspection checklist.

Is a patent or a marketing claim evidence of acoustic performance?

No. Under Article 52 of the European Patent Convention a patent is granted for an invention that is new, involves an inventive step and is susceptible of industrial application; nobody measures sound insulation to grant it. The USPTO describes what is granted as the right to stop others making, using, selling or importing the invention, not a statement that the product performs. A trade name for a pad or core is in the same position until a report backs it.

When a factory offers a patent number, a licence or a trade name for its acoustic layer, file it and ask for the laboratory report on the build-up you are buying. Licences matter for a different reason, freedom to sell in your market, which is covered in what an SPC click licence covers.

How does this work on one order? A worked example

Illustrative only. A UK distributor plans a 5.0 mm SPC board with a 1.0 mm attached IXPE pad for a developer’s apartment project. The factory’s datasheet gives a single IIC figure with no method and no build-up. The developer’s acoustician asks for the covering’s ΔLw.

The buyer asks for the report behind the figure. It is an ASTM E492 report on a concrete slab with a suspended ceiling below, and the specimen is a 4.0 mm board with a 1.5 mm pad from another supplier. The IIC describes that assembly, and the specimen is not the product.

The buyer agrees with the factory to test the order’s own build-up under ISO 10140-3 and ISO 717-2, on boards drawn from the pre-production run, at a laboratory with the method in its scope. The pad’s grade code and supplier go into the specification as controlled fields. The installation instructions state no additional underlay. The acoustician has a ΔLw for the covering on a concrete reference floor and is told, in writing, that the result does not cover the timber-framed block in phase two. The cost was one test and about three weeks; the alternative was quoting a figure that described somebody else’s floor.

Our view

We would decide which noise matters for the market, then buy one tested build-up and freeze it: board, pad material, thickness, grade and supplier, with the report attached to the specification. A figure we could not tie to that build-up would not go on our datasheet or carton.

We would not let a separate underlay into the system unless the factory approves it in writing and a report covers the combination.

If you are building an own-label range and want this written into the specification, our product development support covers sample rounds, test requests and the specification sheet. For quoting the range afterwards, see the specs and quotes guides.

Common mistakes with acoustic SPC specifications

Most acoustic disputes start with a figure that was never tied to the product shipped. The table lists the patterns we would guard against, what each costs and how to prevent it.

Mistake What it costs How to avoid it
Comparing one factory’s IIC with another’s ΔIIC A choice made on numbers that measure different things Ask for the same metric and method from every factory
Accepting a report on another thickness or pad A published figure no document supports Match board and pad field by field
Using a concrete-slab result for a timber-framed building A complaint the lab result never covered State the test floor next to every figure
Writing the pad as “IXPE” only A pad change during production goes unseen Material, thickness, grade code and supplier as controlled fields
Recommending an extra underlay to improve sound Joint damage and a warranty dispute One rule in the installation instructions, agreed with the factory
Treating a patent or trade name as proof Marketing copy with no test behind it Ask for the laboratory report on your build-up

Questions buyers ask

Can I ask the factory to test our exact SKU?

Yes. Name the laboratory method, the test floor, the board and pad build-up and the sample source in the order or a side letter, and agree who pays for the test and who owns the report. A report you commissioned on boards drawn from your production is worth more than any number of reports the factory already holds.

What happens if the pad supplier changes during production?

Treat it as a new construction. The acoustic report no longer describes the goods, so the change needs your written approval, a new sample and, if you publish an acoustic figure, a new report or a written statement from the laboratory that the old one still applies.

Can a distributor quote the factory’s acoustic report in its own literature?

Only for the build-up the report covers and with the method named next to the figure. Ask the factory for written permission to use the report, and keep a copy of the report on file against each published figure.

Is a field test better than a lab report?

It answers a different question. ASTM E1007 measures a finished building, flanking paths included, and ISO 16283-2 is the ISO field method, so the result belongs to that building. A lab report is what lets you compare products; a field test is what a project acoustician uses to check a completed floor.

Sources & further reading

Authorship, affiliations & disclosure

Prepared from the standards bodies’ published scopes and abstracts, an industry association’s guidance, Approved Document E and one supplier’s installation instructions, read on 11 November 2026. The full standards are sold documents and were not read; nothing here restates a requirement beyond the published scope. Building regulations and acoustic requirements for a project are set by the project’s designer and the local authority. The worked example is illustrative.

Corrections & editorial information

Continue exploring.

All guides in Specs & quotes