SPC, LVT, WPC and PVC, floors and panels.Purchasing office · Floors, panels & surfaces
More in Specs & quotes

Specs & quotes / Water claims

Waterproof SPC flooring: three claims, three documents

EN 16511 defines a waterproof panel, joint leakage under 24 h of standing water and a water resistant floor as separate claims. Ask for proof of each.

Short answer

“Waterproof” on an SPC quote bundles three claims: the plank does not swell, the click joint holds back standing water, and the installed floor survives water on its surface. EN 16511:2023 defines each separately. Ask for a swelling or mass-change report on the ordered board, a joint water test on the ordered profile, and the warranty text on spills, standing water and subfloor moisture.

01

EN 16511:2023 defines a water proof panel as one whose materials do not swell or gain mass in contact with liquid water, and joint leakage resistance against water standing on the surface for 24 h.

02

ISO 24336:2005, the thickness swelling method, removes any pre-attached backing before testing, so a swelling report says nothing about an attached pad.

03

Two published rigid-core warranties we read, Shaw (revised August 2026) and RW Supply+Design (April 2022), exclude floods and subfloor moisture; RW does so while calling its planks waterproof.

A factory that writes “100% waterproof” on a quote may be right about the core and still say nothing about the rest. The plank, the joint and the installed floor fail in different ways, are proved by different documents, and are excluded from warranties in different words. Ask for each separately, before the sample is approved.

Which claims sit behind “waterproof” on an SPC quote?

Three claims, and the European product standard for click-locked multilayer panels already separates them. EN 16511:2023 defines a “water proof panel”, a joint’s “resistance to water leakage” against water standing for 24 hours, and a “water resistant floor” that withstands spills on its surface. A report for one is no evidence for the others.

The table maps each claim to the EN 16511:2023 definition (clauses 3.11 to 3.13, read in the official preview) and to the document we would ask for. The evidence column is our method.

Claim on the quote EN 16511:2023 term Evidence to ask for What it does not cover
The plank is waterproof Water proof panel: materials that do not swell or gain mass in contact with liquid water Thickness and mass change after immersion, method and edition named, on the ordered board Joints, pad, subfloor
The joints are waterproof Resistance of mechanical joints to water leakage, standing water for 24 h Assembled-joint water test on the ordered profile and construction Water reaching the perimeter or rising from below
The floor is waterproof Water resistant floor: withstands topical spillages Warranty text and installation instructions for the ordered product Floods, leaks, subfloor moisture (usually excluded)

EN 16511 covers mechanically locked multilayer panels for floating installation, and its definitions include a substrate “based on polymer(s)”, which is where a rigid PVC core sits. It also says the standard applies to areas of frequent wetting, such as bathrooms and laundry rooms, only if the producer specifies it.

What proves the plank will not swell?

A report showing thickness and mass before and after water exposure, on boards of the construction you ordered, with the method and edition named. EN 16511 lists EN 317 and ISO 24336 among its references for thickness swelling after immersion.

ISO 24336:2005 is a destructive laminate method, last confirmed in 2020. Its abstract says any pre-attached soft backing or sub-layer is removed before testing. On an SPC board with an attached pad, the swelling result therefore describes the board alone. If the pad matters to your claim, it needs its own evidence.

The ASTM point catches buyers selling into North America. F3261 is the specification for resilient flooring with a rigid polymeric core, and its abstract covers binder content, dimensions, openings, ledging, residual indentation, dimensional stability and resistance to chemicals, heat, light and static load. The abstract lists no water or swelling test, so “meets ASTM F3261” on a data sheet is not water evidence. Check what any report or certificate scope covers using our notes on how to read a certificate’s scope, and match its construction to yours: thickness, core revision, pad.

Next step: ask every factory for the same water evidence in the quote brief.

What proves the click joint keeps standing water out?

A test of assembled boards with water left on the joint, run on your profile and construction. ISO 4760:2022 is the ISO method: it evaluates moisture resistance to surface water of a joined floating assembly and sets rating criteria. EN 16511:2023 references it, and frames the property as resistance to water standing on the surface for 24 hours.

A tight joint is a precondition, and it is measured elsewhere. Openings, height differences and locking strength are covered in our guide to locking strength and joint gap tests; a joint that fails those will not hold water whatever the water report says.

Three checks on any joint water report. The method and edition are named, not “water test”. The boards are of the ordered thickness, profile and pad, because a padless sample behaves differently at the joint. And the result is stated against a rating or limit you agreed. ISO 4760 is written for laminate, so ask the lab to state that it was applied to a polymer-core panel and how.

Manufacturers say the same thing in their warranties. RW Supply+Design calls its rigid-core planks waterproof and adds, in the same paragraph, that moisture can pass through improperly seated seams, around expansion gaps and room perimeters.

Which water damage do SPC warranties exclude?

Water on the surface for a limited time, and little else. Both rigid-core warranties we read cover surface moisture or spills, then exclude floods, standing water from leaks and anything coming from the subfloor. RW Supply+Design adds that the installed floor is not a moisture barrier. Read the warranty for the exact product before you repeat “waterproof” to your own customers.

The table sets out the exclusions in the two warranties we read: Shaw’s Resilient Rigid Core 15 Year Limited Commercial Warranty (revision dated 28 August 2026) and RW Supply+Design’s Rigid Core SPC warranty (valid April 2022).

Water source Shaw rigid core, commercial RW Supply+Design rigid core SPC What to settle with your factory
Spills on the surface Structural integrity not significantly diminished by surface moisture; damage caused by spillage is still listed among exclusions Covers incidental spills typical of a home The spill window in hours, in writing
Standing water, leaks, floods Excluded: floods, standing water from leaky pipes, hydrostatic pressure Excluded: flooding, leaky plumbing, appliances Whether a leak found within the window is covered
Subfloor moisture All subfloor moisture issues excluded; moisture testing not the company’s responsibility Excluded; impermeable moisture barrier required over concrete Barrier, test method and limit in the instructions
Cleaning water Damage from not following the cleaning guidelines excluded Wet mopping and steam mops excluded Cleaning method printed in the instructions
Walls, trims, subfloor Not covered Not waterproof; mould from trapped moisture excluded Perimeter treatment for wet rooms

Floating and glue-down installations change how water reaches the subfloor and the perimeter; the choice between them is covered in our guide to choosing between floating and glue-down.

1 Spill on surface warranty spill window 2 Through the joint ISO 4760 joint report 3 Perimeter gap: instructions, trims SPC plank: swelling report SPC plank attached pad (outside the swelling test) barrier / subfloor 4 From below: usually excluded
Fig. 1Four routes for water into an installed floor, and the document that speaks to each. Schematic, not to scale.

What should the specification and PO say?

One clause that defines “waterproof” for your order and ties each part to a report, a construction and a retest trigger. Without it, any existing report satisfies the word. The clause belongs in the specification sheet behind an approved sample, so the evidence is fixed before production.

Suggested wording, to adapt with your adviser:

Water claims. “Waterproof” in this order means all three of the following. (1) Panel: change in thickness and mass after water exposure, tested to [method and edition] on boards of the approved construction [thickness, core revision], with the treatment of the attached pad stated in the report; acceptance [agreed value]. (2) Joints: resistance of assembled long-side and short-side joints to standing water, tested to ISO 4760:2022 on the approved profile and construction including pad; acceptance [agreed rating]. (3) Installed floor: the supplier provides the installation instructions and warranty text for the ordered product, stating the areas of use, any wet rooms allowed, the period for which surface water is covered, and the subfloor moisture test, limit and barrier required. The word “waterproof” appears on packaging and documents only as defined in this clause. A change of core recipe, pad or click tooling requires a retest of (1) or (2) before shipment.

Worked example: a waterproof report that covered the wrong part

Illustrative only. A UK distributor plans a 5.5 mm SPC plank (4.5 mm board plus 1.0 mm attached pad) for kitchens and bathrooms. The factory’s quote says “100% waterproof” and attaches a lab report as proof. Read against the three claims, the report speaks to one of them, on a thinner board without the pad.

Claim What the buyer needed What the factory sent Action
Panel Swelling and mass change, method named, ordered board Thickness swelling, 4.0 mm board, pad removed, method named Not the ordered board; ask for a retest on the 4.5 mm board
Joint Joint water test, ordered profile with pad Nothing Ask for an ISO 4760:2022 test on the 5.5 mm padded board
Floor Warranty and instructions naming bathrooms A one-page sales sheet Ask for instructions and warranty text; drop “bathroom” until they exist

The panel retest and the joint test come back on the ordered build. The factory’s instructions name kitchens but not bathrooms, so the distributor removes bathrooms from its range sheet and keeps “waterproof core” on the carton. The same approved boards go into the wear layer and core check, so all results describe one board set.

Our view

We would never accept “waterproof” as a single line on a quote. We would ask for the panel report and the joint report on the construction we are buying, and for the installation instructions and warranty text before the sample is approved. Where the product documents do not name wet rooms, we would not sell it into them.

We would ask for the joint report first: it describes the place where standing water sits on a laid floor. The swelling report proves the least about an installed floor, because it tests the board on its own. Our product development support writes the water clause into the specification with the factory; for the other quote and specification checks, see the specs and quotes guides.

Common mistakes with waterproof claims

Most disputes start with a word on a carton that no document defines. The table lists the usual gaps between the quote and the evidence.

Mistake What it costs How to avoid
Promising end users more than the factory warranty You carry the difference Copy exclusions into your own warranty
No retest after a pad, recipe or tooling change New build ships on old evidence Make each change a retest trigger in the PO

Questions buyers ask

Is SPC flooring waterproof or only water resistant?

It depends which part you mean. EN 16511:2023 calls a panel water proof when its materials do not swell or gain mass in liquid water. The click joint and the installed floor are separate claims with their own tests and warranty terms, so ask for evidence of each before you print “waterproof”.

Can the factory print “100% waterproof” on my cartons?

It can print what you approve, but the claim on a private-label carton is yours to stand behind with retailers and end users. Approve only wording your reports and warranty support, such as “waterproof core” with the joint and installation conditions stated in the instructions.

Is an SPC floor suitable for a bathroom?

Only where the installation instructions and warranty for that product name it. Ask for installation instructions that name the room, the perimeter treatment and the moisture barrier, and for a warranty that does not exclude it.

What happens if the factory changes the attached pad supplier mid-contract?

Treat it as a new construction for the joint test and for any claim that includes the pad. The swelling report on the board may still stand, because the method tests the board without its backing, but the joint result and the pad itself are no longer covered by the old evidence.

Who gives the end user the waterproof warranty on a private-label floor?

You do. The factory backs you only as far as your supply contract says. Before you publish a warranty, check that every promise in it is matched by a report or a factory obligation in the PO, including the spill window and the areas of use.

What if cartons arrive wet from a container leak?

That is a transit loss, not a product claim, and the plank tests do not help you. Record it before unloading and follow the steps for [claims on a damaged container](/intelligence/defective-container-claims/).

Sources & further reading

Authorship, affiliations & disclosure

Prepared from the standards catalogue records, the EN 16511:2023 official preview and the two manufacturer warranties listed, read on 11 November 2026. Test procedures of ISO 24336 and ISO 4760 are paid texts and are not described here. The worked example is illustrative. We did not test any product for this guide.

Corrections & editorial information

Continue exploring.

All guides in Specs & quotes