Specs & quotes / Payment terms
Flooring factory deposit and payment terms: what releases each payment
Tie each flooring factory payment to evidence: under UCP 600 a bank checks the documents alone, and the FBI says confirm bank changes by phone.
Short answer
Agree before the deposit what evidence releases each payment and who may change the bank details. Pay only an account in the contracting company’s legal name, confirmed by a call to a number you already hold. Release the balance on a passing independent inspection and loading evidence, never on a bill of lading copy alone. Put all of it in the purchase order before the pro forma is paid.
The FBI’s IC3 counted US$55.5 billion in domestic and international exposed business email compromise losses between October 2013 and December 2023.
Under UCP 600, a bank decides on the documents alone whether a presentation complies, and documents with conflicting data do not comply (ICC Banking Commission, November 2024).
Trade.gov notes that a letter of credit protects the buyer because no payment obligation arises until the goods have been shipped as promised. Shipped is not the same as inspected.
The deposit is the one payment you make on trust. Every payment after it can be tied to a document, provided the purchase order says so before the first transfer. This guide covers how to tie each payment to evidence, how far a letter of credit goes, and how to stop a balance landing with someone who is not the factory.
What should be agreed before the deposit is paid?
Four things, in writing: the legal name and account that will receive every payment, the evidence that releases each instalment, who on your side signs each release, and how a change of bank details will be confirmed. They belong in the purchase order or a payment schedule attached to it, signed before the pro forma invoice is paid.
The table is our method for a T/T order. No standard sets these triggers; the shares are whatever you negotiate.
| Payment | Released when you hold | Signed off by | Still at risk after paying |
|---|---|---|---|
| Deposit | Signed PO with the specification annex; account in the contracting company’s legal name, confirmed by call-back | Your authorised signatory | The deposit itself, until the goods exist |
| Balance | Passing independent inspection on the agreed plan; loading photos tied to the inspected pallets; draft bill of lading matching invoice and packing list | You, after reading the report | Transit damage; defects the sample did not catch |
| Retention (if agreed) | Arrival and a check period with no defect notified | You | Defects found after the check period |
| Change of account | Letter on letterhead, then a call to a number from your own records, approved by a second person | Two people on your side | Nothing, if the check comes before the payment |
The name on the account matters as much as the number. An account held by a sister company, a trader or a person is a question to settle before the deposit, and our guide to checking whether a seller is the plant it claims to be covers matching the contract and the bank account against the certificates.
What does each T/T split expose you to?
Everything paid before the goods exist and pass inspection is exposed to non-delivery and to a lot that fails. The factory, in turn, carries whatever it spends on material and line time that you have not paid for. A bigger deposit moves risk to you; a balance tied to evidence moves some of it back. The split is a negotiation.
Trade.gov’s guidance on payment methods sets out both ends. Payment in advance is the least attractive option for the buyer, because the goods may not be sent once paid. Open account is among the most advantageous for the importer. A T/T deposit and balance sits between the two, and where it lands is set by the contract, not by any published norm. A factory buying PVC resin and decor film for your run has a fair case for a deposit; it has no case for being paid in full before anyone independent has seen the goods.
The trigger for the balance is the term you can most usefully move, and the next section starts there. How the price side of the quote is built is covered in what makes up an SPC FOB price.
When should you release the balance?
After a passing independent inspection on the agreed plan, and after loading evidence that ties the inspected pallets to the sealed container. A bill of lading copy shows the carrier took a number of cartons under a seal; it says nothing about the boards inside. Pay on a copy alone and quality becomes a claim at destination, no longer a decision you take before shipment.
The table sets the common balance triggers against what you hold when you pay. The order follows the shipment; the right row is the latest one the factory will accept.
| Balance trigger | What you hold when you pay | Risk you still carry |
|---|---|---|
| Before inspection | The factory’s own production photos | Paying for a lot nobody independent has seen |
| After a PASS report, before loading | The report on the agreed plan | Goods swapped or short-loaded between inspection and seal |
| After PASS, against loading photos and a bill of lading copy | Report, photos, seal number, the carrier’s bill | Transit damage; defects the sample did not catch |
| After arrival | The goods | The factory carries the exposure, so expect resistance on a first order |
The inspection has to be specified before it can trigger anything: plan, defect classes, sample size and timing are set out in our pre-shipment inspection checklist. If the report says FAIL, the balance stays where it is until a re-inspection passes or you sign a concession; the options after a failed report are set out in a separate guide.
Does a letter of credit protect the buyer?
Partly. It gives the factory a bank’s commitment and gives you control on paper: nothing is paid unless the listed documents are presented and agree with each other. None of those documents is the floor. Quality enters the credit only if you make an inspection certificate a required document and define what it must say.
ICC’s Banking Commission describes the test as a comparison of data across the stipulated documents. It works for you only when those documents carry the data you care about. “Goods of good quality” cannot be checked on paper; “inspection certificate issued by a named inspection body, stating PASS for PO 1234 on the agreed plan” can. Trade.gov warns that credit documents are detailed and prone to errors and discrepancies, and that errors must be amended and resubmitted, so keep the list short and every requirement checkable.
The table lists the documents we would ask for in a credit for an SPC order, and what each one should state.
| Document | What the credit should require | What it ties payment to |
|---|---|---|
| Commercial invoice | Seller’s legal name as on the contract; PO number; goods described as in the specification | Your contract |
| Packing list | Cartons and m² per decor and batch | The lot that was inspected |
| Bill of lading | Shipped on board; ports; latest shipment date | Booking and timing |
| Inspection certificate | Named inspection body; result PASS; PO number; agreed plan; dated before loading | Quality, the only document that speaks to it |
| Certificate of origin (if your market needs one) | Issuer and form named | Duty treatment at import |
If the factory asks you to accept documents that do not match, ask which document and why. Ask the same of every mismatch: does the data conflict, or does it only differ in wording? An inspection certificate for another PO number is a conflict about the lot itself, and it means the lot you are paying for has not been inspected.
How do you check a change of bank details?
Treat every change as false until it is confirmed outside email. Call the factory on a number you held before the request arrived, from the contract or an earlier invoice, never one printed in the message. A second person approves the new details, the account name must match the contracting company, and only then does money move.
FBI guidance points the same way. A 2023 IC3 announcement, written about criminals posing as buyers to defraud vendors, advises calling a business’s main phone line rather than numbers provided via email; the 2024 announcement tells businesses to verify changes in account information through secondary channels, to verify the sending address and to watch for misspelt domains.
IC3 describes spoofed company domains and the names of real or invented employees, so the request will look routine: a familiar sender name, a domain one letter off, a plausible reason. A genuine change survives a phone call and a short delay. A fraud depends on neither happening.
Write the rule down before the first order and give it to whoever presses “send” in your accounts team. The person paying the balance is rarely the person who negotiated with the factory, so the rule has to be on paper.
How does this work on one order? A worked example
Illustrative only. A UK distributor places a first order for two 40ft containers of SPC with a plant in northern Vietnam: T/T with a 30% deposit and a 70% balance, the split both sides negotiated. The PO makes the balance due within three working days of a PASS report on the agreed plan, loading photos with the seal number, and a draft bill of lading that matches invoice and packing list.
Before the deposit, the buyer calls the plant’s main line, taken from its signed quotation, and confirms the account named on the pro forma. The account is in the plant’s legal name. Production runs to schedule and the inspection passes.
Two days later an email arrives from the sales manager’s address. The balance should go to a new account in Hong Kong, in a trading company’s name, “because of our annual audit”, with a mobile number for questions. The domain has one letter changed. The accounts clerk follows the written rule and passes it to a second person, who calls the main line from the quotation. The sales manager has sent nothing. The buyer pays the original account, the loading photos and seal number arrive the same day, and the factory releases the originals. The buyer also tells the factory, whose mailbox or contacts list has been exposed. The check cost one phone call and half a day.
Our view
We would tie the balance to a report from someone other than the factory, and keep the deposit at what the factory accepts for a first order. Better terms come on repeat orders, once the evidence has held. The trigger matters more to us than the share.
A letter of credit can be worth its paperwork on a large first order with a plant you have not bought from, and only if the credit names the inspection certificate and its wording. Without that, the bank is checking paper that says nothing about the floor. For bank changes we would run the two-person rule from day one, written into the payment schedule so the factory knows it in advance.
Our buyer-side purchasing office can draft the payment schedule with you and check each document before you release a payment; the payment itself stays with you. For quote and specification work before the order, see the specs and quotes guides.
Common mistakes with deposits and balances
Most payment losses we would guard against come from a trigger that was never written down or a check that was skipped once under time pressure. The table lists them with what each costs and how to prevent it.
| Mistake | What it costs | How to avoid it |
|---|---|---|
| Balance against a bill of lading copy with no inspection | Quality becomes a claim at destination | PASS report as a condition before loading |
| Taking bank details from the pro forma alone | The first payment may reach the wrong party | Call-back and legal-name match before the deposit |
| Changing the payee on an email | The balance goes to a fraudster | Two-person approval and a call to a number you already hold |
| Letter of credit with no inspection certificate | The bank pays on compliant paper whatever the floor | Name the certificate, the issuer and the wording |
| Raising the deposit to win a lower price | More money exposed before the goods exist | Negotiate price on its own; keep the trigger |
| Agreeing a payment change in a chat | No clear record of what changed | Signed amendment to the payment schedule |
Questions buyers ask
Can I ask for a smaller deposit on a repeat order?
Yes, and a clean first order is your argument. Offer something the factory values in return, such as a firm forecast or a longer production window, and keep the balance trigger unchanged. A lower deposit bought with a weaker trigger is no gain.
What happens if the factory will not load until the balance is paid?
Then the balance has to follow the inspection, not the bill of lading. Book the inspection early enough for the report to reach you before the loading date, pay within the agreed days of a PASS, and have loading supervised so the goods you paid for are the goods in the container.
What if we have already paid into a fraudulent account?
Contact your bank at once and ask it to recall the funds; the FBI’s IC3 advises this immediately and also advises filing a complaint at ic3.gov whatever the amount lost. Tell the factory, whose mailbox may be compromised, and keep the emails.
Should the deposit go to the factory or to a trading company that sells for it?
To the company named as seller on your contract, whichever it is. If a trader is the seller, its name should be on the contract, the invoice and the account, and you should still know which plant makes the goods. A payee that matches neither needs an explanation before any money moves.
Can part of the balance be held until the goods arrive?
You can propose a retention released after arrival and an agreed check period. Expect resistance on a first order. If it is agreed, the payment schedule should state the period, the check, who carries it out and what happens to the retention when you notify a defect.
Sources & further reading
- International Trade Administration (Trade.gov): Methods of payment (read November 2026)
- International Trade Administration (Trade.gov): Letter of credit (read November 2026)
- ICC Banking Commission: Technical Advisory Briefing No. 12, UCP 600 sub-article 14 (d) (13 November 2024)
- FBI IC3: Business Email Compromise, the $55 Billion Scam, public service announcement (11 September 2024)
- FBI IC3: Business email compromise tactics used to acquire commodities and defraud vendors, public service announcement (24 March 2023)
Authorship, affiliations & disclosure
Prepared from the official sources listed, read on 11 November 2026. No official source sets a normal deposit share for flooring orders, so the splits shown are illustrative, as is the worked example. This is purchasing guidance, not legal or financial advice; have payment terms and letter of credit wording reviewed by your bank and your adviser.
Corrections & editorial informationContinue exploring.
All guides in Specs & quotesSPC flooring and sun exposure: gaps, glazing and fade evidence
SPC flooring in direct sunlight: one maker doubles its 5 mm gap to 10 mm where sun comes through glass doors. What to ask for before you approve a decor.
Read the guideSPC flooring gloss level: how to specify a matt finish that repeats
Name the geometry, target and tolerance: ISO 2813 reads gloss at 20°, 60° or 85°, and its scope covers non-textured coatings only.
Read the guideAcoustic SPC flooring: how to specify and verify the sound rating
Acoustic SPC flooring claims rest on one lab build-up: ASTM E2179 rates the covering on a concrete slab, not your building. What to ask for.
Read the guide